The Dyson DC27 High-Reach Cleaning
Caution:
- Switch the ‘OFF’ vacuum before changing tools.
- Powerful suction can cause the hose to ‘pull back’ – please take care.
- Take extra care when vacuuming on stairs; do not work with the vacuum above you on the stairs. Do not put the vacuum on chairs, tables, etc.
- Ensure the vacuum is in an upright position before using tools.
PLEASE NOTE: - To release the wand, open the wand cap and pull the red tube until the wand releases from the vacuum. Tools can be attached to either the hose or wand.
- The brush bar will not rotate when the vacuum is in an upright position.
- Ensure the wand cap is closed when not in use
The Dyson DC27 Clear Bin Emptying
Caution:
- Switch ‘OFF’ vacuum and unplug the vacuum before emptying the clear bin
- Empty as soon as the dirt reaches the level of the MAX mark – do not overfill. To remove the clear bin from the vacuum press the button at the rear of the cyclone carrying handle. To release the dirt, press the red clear bin release button.
- Do not use the vacuum without the clear bin in place.
- To minimize dust/allergen contact when emptying, encase the bin tightly in a plastic bag and empty it. Remove the bin carefully and seal the bag tightly, dispose as normal.
The Dyson DC27 Clear Bin Cleaning
Caution:
- Do not immerse the whole cyclone in water or pour water into the cyclone.
- Ensure the clear bin is completely dry before replacing it.
PLEASE NOTE: - Do not use detergents, polishes, or air fresheners to clean the clear bin.
- Do not put the bin in a dishwasher.
- When vacuuming, certain carpets may generate small static charges in the clear bin. These are entirely harmless and are not associated with the main supply. To minimize any effect from this, do not put your hand or insert any object into the clear bin unless you have first emptied it and rinsed it out with cold water.
- Clean the shroud with a cloth or dry brush to remove lint and dust.
The Dyson DC27 Washing Your Filter
Caution:
- Switch ‘OFF’ and unplug the vacuum before removing the filters.
- Ensure filters are completely dry before refitting to the vacuum.
PLEASE NOTE: - This vacuum has two filters, located as shown. It is important to check your filters regularly and wash at least every 3 months according to instructions, to maintain performance.
- The filter in the ball should be rinsed and tapped out until the water runs clear, then tapped out again to ensure all excess water is removed. Please leave to dry completely for 24 hours.
- It is normal for this filter in the ball to turn grey in color. The filters may require more frequent washing if vacuuming fine dust.
- Do not use detergents to clean the filters.
- Do not put the filters in a dishwasher, washing machine, tumble dryer, oven, microwave, or near an open flame
The Dyson DC27 Looking For Blockages
Caution:
- do so could result in personal injury.
- Please ensure the vacuum is upright and switched off before removing the hose or airway inspection parts.
- Beware of sharp objects when clearing blockages.
- Refit all parts of the vacuum securely before using it.
PLEASE NOTE: - Clearing blockages is not covered by your vacuum’s limited warranty.
- This vacuum is fitted with a thermal cut-out. If any part of your vacuum becomes blocked, it may overheat and then automatically shut off. Switch ‘OFF’ unplug the vacuum and leave it to cool down for at least 60 minutes before attempting to check filters or for blockages. Clear blockage before restarting
The Dyson DC27 Clearing Brush Bar Obstructions
Caution:
- Switch off and unplug the vacuum before clearing brush bar obstructions. Failure to do so could result in personal injury.
- If your brush bar is obstructed, it may shut off. If this happens you will need to remove the brush bar as shown and clear any obstructing debris. Refit all parts securely before use.
- Beware of sharp objects when clearing obstructions.
- Refit all parts of the vacuum securely before using it.
PLEASE NOTE: - Cleaning the brush bar obstructions is not covered by your vacuum’s limited warranty.