Dolphin Liberty 200 Troubleshooting

If you are having problems with your Dolphin Liberty 200 Pool Cleaner, you are not alone. Many Dolphin Liberty 200 owners experience issues with their pool cleaner from time to time, and it can be frustrating to deal with these problems.

I have problems with my Dolphin Liberty 200

Dolphin Liberty 200 Pool Cleaner Problems

The Dolphin Liberty 200 doesn’t charge

Cause Solution
  • Robot’s Battery LEDs are blinking in a special pattern (central LED
    – then right and left LEDs). The issue occurred while the robot was connected to the charger
  • In case the robot feels hot to the touch: charge the robot in a shaded location or when the temperature is low, for example: overnight / indoors.
  • In case the robot feels cold to the touch: try charging the robot in a warmer location.
  • The Power Unit doesn’t show any LEDs at all
  • Try connecting the charger to a different power outlet.
    Make sure that the charger LED is on.
  • The Power Button LED is red
  • Try disconnecting the charger from the Power Unit and
    connecting it back a few times.
  • Check whether an object is blocking the connection between the charger and the Power Unit.
  • The charging process stops, and the Power Button LED is blinking red for a short period of time
  • Make sure that the charger is connected properly.
  • Check whether an object is blocking the connection between the charger and the Power Unit.
  • Charging progress is stuck: one of the battery LEDs is blinking and
    doesn’t switch to the steady light after a long period of time
  • Check that the charger LED turns on.
  • Make sure that the charger is connected properly.
  • Check whether an object is blocking the connection between the charger and the Power Unit.
  • Charge overnight in a cooler location.

The Dolphin Liberty battery is not full after charging

Cause Solution
  • The robot’s battery discharges while the robot is turned off
  • Fully charge the robot (until all battery LEDs are steady green), make sure that the robot is turned off. Do not start the cleaning process. Check the battery status after 2 days. If the battery charge level is significantly lower – contact Customer Care.

The Dolphin Liberty Red LED light appears above the power button

Cause Solution
  • Make sure there’s nothing stuck in the tracks or brushes. Clean the filter and make sure it’s not clogged. Disconnect and reconnect the charger 3 times.

The Dolphin Liberty will not start the cleaning cycle. The Power Button LED is red

Cause Solution
  • The charging process works properly The robot finishes a 90-minute cleaning cycle During the Eco mode and Cycle Selector, the robot will climb the walls even if configured otherwise
    The robot will not respond to Click-UpTM properly – will start the cleaning cycle instead of waiting at the wateline
  • Contact Customer Care: wecare@maytronics.com
  • The charger is connected to the robot
  • Disconnect the charger and press on the robot’s power button to operate.
  • The charger is disconnected from the robot. The charging process works properly
  • Contact Customer Care: wecare@maytronics.com

Dolphin Liberty 200 Replacement Parts

Troubleshooting a Dolphin Liberty 200 Pool Cleaner

Share your Dolphin Liberty 200 Pool Cleaner Problems, issues , tips, ideas, and frustrations with other owners.

  1. My Dolphin when plugged in to charge it goes to charged [red] then to fully charged [green] after ten minutes other times it goes to fault [yellow]
    I have disconnected the battery and reconnected it many times and it works sometimes.

    Reply

Dolphin Liberty 200 Issues? Need Help?

Users are encouraged to share their tips or frustrations with their Dolphin Liberty 200 with the community by leaving a comment. Sharing insights and experiences can help other users get the most out of their pool cleaner and avoid common issues.

Share your Thoughts or Describe your problem below:

The maximum upload file size: 5 MB. You can upload: image. Links to YouTube, Facebook, Twitter and other services inserted in the comment text will be automatically embedded. Drop files here